Front end alignment specification
NEWS
 

  1. Welcome to Honda Odyssey Forum : Odyssey Minivan Forums General discussion forum for Honda Odyssey

    Welcome to Honda Odyssey Forum : Odyssey Minivan Forums - a website dedicated to all things Honda Odyssey.

    You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, Join Honda Odyssey Forum : Odyssey Minivan Forums today!
     
+ Reply to Thread
Results 1 to 2 of 2

Thread: Front end alignment specification

  1. #1
    Registered User
    Join Date
    Jan 2009
    Location
    NY
    Posts
    2

    Front end alignment specification

    My Hanes manual does not give the alignment specs. for my 2001. Can someone tell me what the toe in (or out ) spec is? I had a blowout and the front is now toeing out.

  2. Remove Advertisements
    OdyClub.com
    Advertisements
     

  3. #2
    Registered User New Dad New Van's Avatar
    Join Date
    Dec 2003
    Location
    Canada
    Posts
    5,696
    Front Toe Inspection/Adjustment

    Use commercially-available computerized four wheel
    alignment equipment to measure wheel alignment
    (caster, camber, toe, and turning angle). Follow the
    equipment manufacturers instructions.

    1. Check the tire pressure.
    2. Center the steering wheel spokes.
    3. Check the toe with the wheels pointed straight
    ahead.

    Front toe: 0 +- 2 mm(0 +- 1/16 in.)

    If adjustment is required, go to step 4.
    If no adjustment is required, remove the
    alignment equipment.
    4. Loosen the tie-rod locknuts, (14 x 1.5mm
    44 Nm (4.5 kgfm, 33 lbfft) and turn both
    tie-rods in the same direction until the front
    wheels are pointing straight ahead.
    5. Turn both tie-rods equally until the toe reading on
    the turning radius gauge is correct.
    6. After adjusting, tighten the tie-rod locknuts.
    Reposition the tie-rod boot if it is twisted or
    displaced.
    2001 Odyssey LX
    2003 ACURA EL Touring

    UNOFFICIAL 2001 ODYSSEY THREAD: http://www.odyclub.com/forums/showth...664#post384664

  4. Remove Advertisements
    OdyClub.com
    Advertisements
     

Similar Threads

  1. Front end alignment question / loose lug nuts
    By tjhenn in forum 1999 - 2004 Odyssey
    Replies: 7
    Last Post: 07-15-2011, 11:11 AM
  2. 2007 front end alignment-left front xtra wear?
    By HiVel in forum Problems and Concerns
    Replies: 10
    Last Post: 05-03-2010, 02:44 PM
  3. Where in the manual is the torque specification?
    By raymondjiii in forum 2005 - 2010 Odyssey
    Replies: 3
    Last Post: 11-18-2007, 06:12 PM
  4. front end alignment on Touring
    By mjones5 in forum 2005 - 2010 Odyssey
    Replies: 3
    Last Post: 01-30-2005, 03:51 PM
  5. Type "2" Coolant Specification Number?
    By J. Tupp in forum Periodic Maintenance
    Replies: 3
    Last Post: 11-04-2003, 03:41 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Powered by vBadvanced CMPS v4.1.2