Honda Odyssey Forum banner

Select the option that matches your AT/issues.

  • Honda 10AT (10 speed) - Fluid drain-n-fill or software update

  • Honda 10AT (10 speed) - Solenoid replaced**

  • Honda 10AT (10 speed) - Computer replaced

  • Honda 10AT (10 speed) - Torque converter replaced**

  • Honda 10AT (10 speed) - Loss of power on econ

  • Honda 10AT (10 speed) - Loss of power on econ off

  • Honda 10AT (10 speed) - Rough Shifting

  • Honda 10AT (10 speed) - Transmission replaced

  • Honda 10AT (10 speed) - No Issues

  • ZF 9HP (9 speed) - Fluid drain-n-fill or software update

  • ZF 9HP (9 speed) - Solenoid replaced**

  • ZF 9HP (9 speed) - Computer replaced

  • ZF 9HP (9 speed) - Torque converter replaced**

  • ZF 9HP (9 speed) - Loss of power on econ

  • ZF 9HP (9 speed) - Loss of power on econ off

  • ZF 9HP (9 speed) - Dog clutch noise (4-5, 7-8 gears) or Other noise

  • ZF 9HP (9 speed) - Rough Shifting

  • ZF 9HP (9 speed) - Transmission replaced

  • ZF 9HP (9 speed) - No Issues - Normal dog clutch click (4-5, 7-8 gears)

  • ZF 9HP (9 speed) - No Issues

  • ZF 9HP (9 speed) - Service Bulletin 19-124 fixed everything

  • ZF 9HP (9 speed) - Service Bulletin 19-124 did not fix anything

Transmission Survey + 9/10 speed detailed info (One thread to rule them all)

42593 154
NOT REPORTED IN THE SURVEY /\
[9 speed failures: 2]
[10 Speed failures: 9]


Not trying to beat this into the ground...just trying to be informative to the community and those that might be experiencing issues. Feel like this should've been created back in 2017/18. On top of that there are so many threads on specifically the 9 speed it can be confusing.

Things to note: 9 Speed is designed by ZF Friedrichshafen Germany, made in South Carolina USA. The 10 speed is designed by Honda in Japan, made in Georgia USA.

Goal of both AT is to save fuel. On average they are fairly the same in MPG. However, they behave differently due to the design. Traditionally AT uses friction clutches resulting in some slip which means transitioning form one gear to another is smooth. 10 Speed is designed as such. 9 Speed on the other hand uses dog clutches between 4-5 and 7-8th gear shifts where no slip can take place, these gears have to in perfect sync for them to mesh together. This results in delayed shifting, a click noise.

ZF 9HP (9 speed)
This AT is notorious and has a pretty bad track record from when it was originally introduced in early Chrysler models. Lots of TLX (2015) Pilot (2016-17) Including MDX had serious issues. Many got their AT replaced. Acura even extended warranties to 10 years on the newly installed AT. ZF blamed most of these issues to how the transmission was programed causing drama. lot of failures with 9HP in the early Pilots and MDX are due to coolant and ATF mixing. This has been addressed at h/w level and with extended warranties. 2019+ has other internal h/w improvements.

This is AT is used still in MDX, Pilot, Passport, Ridgeline in the honda/acura family as of now. Again lots of complaints from the 2016-2017.

On the recent models... overall 99%+ complaints are about shift quality, particularly from 4-5 & 7-8 up/downshifts. This is due to the dog clutch mentioned above. It’s different and takes a little getting used to. ZF for some reason made this into a learning AT. This transmission "learns" how you drive. So Imagine if you have 2+ drivers in the house. ZF even blamed this unpredictable behavior on the customers Link.

TOWING:
ZF 9HP specs are great on paper. Technically it's a bit over built for the Honda J series v6.
Total weight: (wet) 90 Kg / 198.42 lbs
Max torque rating: 500 Nm / 368.7811 ft lbs
(Odyssey: 262 ft lbs)

Even with the great specs Odysseys with the ZF can only tow 3000 lbs.
This may have to do with cooling the unit, Honda never bothered to make this official.
Part:
ATF Cooler Kit (9-Speed AWD)
Instructions for pilot:
https://www.collegehillshonda.com/instructions/pilot/2021/5ezcooler.pdf

It should work on the Ody but the mount points and path for running lines will not exist on the van as is on the pilot or other Honda/Acura's

MAINTENANCE:
The fluid replacement process on the ZF is a chore and unnecessarily convoluted. Expect to pay $350 or more at the dealer. Fluid prices have gone down form $50 to ~$25
for Honda ATF-TYPE 3.1. FYI, it does have a fill bolt on the top and is quite accessible.

To put this thing on neutral without battery you need a key tool (07AAA-TZ3A100) $200. This is also very accessible from the top. (Honda used to just have simple a shift lock back in the day)

Chrysler Pacifica so far is the only vehicle that have tamed this transmission working directly with ZF. Unfortunately Honda is not there yet. Small effort was made with a Service Bulletin19-124.

---

Honda 10AT (10 speed)
This is the future. Most folks report this AT is very smooth and trouble free but there are issues and several failures reported here. This is expected with a brand new product. The 10AT fairly new still so it may or may not have issues. What’s for certain is that even this 10AT will continue to be refined as it gets more application over time. (Personal history, I've never had any issues with most Honda transmissions from the early 90's to now. My parents 03 Ody had 1 transmision replaced at 160k miles. See my list of vehicles)

TOWING:
With the 10AT the Ody can tow full 3500 lbs. No cooler needed. It would be interesting to see if coolers appear on the market when MDX + Pilot switch over this this AT.

Total weight: 220lbs
Max torque rating: 280ft-lbs-354ft-lbs (range form other acuras)
(Odyssey: 262 ft lbs)

MAINTENANCE:
The fluid replacement process is much cheaper/simpler on this AT. Honda ATF-TYPE 2.
The Fill bolt is in the front and faces the radiator and uses a typical 17mm, 6-point head. It is accessible from the engine bay, preferably from the bottom. The drain is the typical 3/8" style. Here is a DIY from smufguy >> DIY - 10spd ATF change

To put this thing on neutral without battery you need to remove the front cover, intake tube, battery and then you need to use an open-end wrench. (Honda used to just have simple a shift lock back in the day)

--------------

No one knows the longevity of the 5th Gen Odyssey. Everything is new and we don’t have any long term usage/mileage to report back. As mentioned 9 speed's primary complaint is shift quality, specifically dog clutches. Not many all out failures reported here. The 10 speed is preferred, shifts much smoother but has several failures reported here. The numbers are too low to mean anything atm. YMMV.

Admins, would love to have this pinned. If this is useless please get rid of it.

---

Honda 10AT (10 speed) fails: 9 reported
(2 failures ^here^)

Honda 10AT (10 speed) issues


---

ZF 9HP (9 speed) fails: 2 reported

ZF 9HP (9 speed) issues
I'm sure there are more...

---

**These are sealed units. AT gets replaced as an entire unit, Dealers do not take these apart. (Please correct me if I am wrong)
1 - 20 of 38 Posts

· Registered
2019 EX-L
Joined
·
306 Posts
Discussion Starter · #2 · (Edited)
Anyone know more on the 10 speed in terms of specs? weight, torque? I've updated this info above. 👆

please verify.
 
  • Like
Reactions: seanpw

· Registered
2019 EX-L
Joined
·
306 Posts
Discussion Starter · #5 · (Edited)
This could help those that are having shifting issues on ZF 9HP. You can reset the transmission. Full disclosure, I did not try this because my van has learned how my wife and I drive. So far things are working great. But in case you need to do a relearn try the following. This has served the Acura folks very well. I'd give it a try if you are having shifting issues. I'd do this if the van was purchased second hand.

Here are the instructions for doing a transmission reset.

1) Push the START/STOP button: press it twice without pressing the brake pedal. DO NOT START THE ENGINE. Turn off the lights and radio.

2) Your dash lights should be on at this point. Within 5 seconds of turning on the ignition, press the gas pedal down all the way, and keep it pressed for 15 to 30 seconds.

3) After the transmission has reset, the CEL will go off.

4) Turn the car off and restart it.

There will be no confirmation or beep but at this point, the transmission has been reset. If you are not sure, repeat the procedure one more time.


Now drive 500+ miles for the full learning to take place.


This may work on the 10 speed? But I don't think the 10 speed is a learning AT. Please verify. + would love more folks to vote.
 
  • Like
Reactions: Qost

· Registered
2019 EX-L
Joined
·
306 Posts
Discussion Starter · #7 ·
smufguy, thanks for the feedback I’ll go and fix these once I’m at a computer. I’m on a mobile phone and usually get some time to do this stuff when all the kids are napping/late at night.

I wish I had access to this information when buying my van. There is so much noise otherwise. On top of that folks only post if there are issues in these places.
 

· Registered
2019 EX-L
Joined
·
306 Posts
Discussion Starter · #9 ·
Just made some tweaks according to smufguy's input. Took too long, I didn't get a chance to get back on here in a long while. Thanks to everyone that have voted. (Please remember I am not an expert, I visit this place once in awhile to see what's happening in the world of minivans of all things, as interesting as it sounds.)
 

· Registered
2019 EX-L
Joined
·
306 Posts
Discussion Starter · #11 ·
At 66K we are told we need a new transmission at the tune of $6K as it is just outside of warranty.
Ahhh.. that’s terrible. Please record this on the survey.

Also, would love hear back updates on the replacement unit.

This is the only way we can record these events for now. On the long run if this survey is still being updated it may help us out. I know there is a class action lawsuit on the ody 9 speed. Not on failures but the shift quality.

shoot we see significant numbers we might be able to class action that too..

All best.
 

· Registered
2019 EX-L
Joined
·
306 Posts
Discussion Starter · #14 ·
65K miles is too early for issues - debating whether to get rid of completely or replace.
Too early for sure. Totally unacceptable.

Did you replace the transmission fluid
I’d like to know too. Personally I’m planning every 30k. So far so good but I don’t have many miles on the van.

ZF makes an awesome 8 speed. The 9 speed is kind of a shame. I wish Honda would at least do something, Chrysler did recalls and replacements too.
 

· Registered
2019 EX-L
Joined
·
306 Posts
Discussion Starter · #18 ·
We bought our 18 EXL with 24k about a month ago and around 25mph it’ll suddenly lose power and slam into gear. You can hear an audible click when this shifting happens. Also, it wants to lurch forward if you barely step on the pedal. I tried resetting the transmission and drove it for 500 miles and it’s still doing it. I have an appt for Wednesday. I’m running all VLEDs but I was having the issue prior to the LED swap. Thankfully we paid the extra 1400 to get Honda Care for 8 years and 100k miles. I’ll post updates after our Wednesday visit.
This is awful. I noticed this 9 speed to be noisy/jerky when particularly cold. After driving a bit it smooths out. Unfortunately all this is coming from the design of the AT. Did you ever get the Software update: http://www.urvi.net/forumfiles/SB/A19-124.PDF
Ask for this at your visit if you didn’t get this yet.
 

· Registered
2019 EX-L
Joined
·
306 Posts
Discussion Starter · #20 · (Edited)
When you got this update, did it help at all?
It’s a mix bag of experience for everyone. What I noticed is that shifting in steady acceleration has improved a lot as in no jerking or clicks. The key is you put your foot down and keep it steady. Any fluctuations at the accelerator the AT won’t know what to do. Down shifts are not as smooth as up shift. I do sometime hear the dog clutch 4-5th and 7-8th (more on 4-5th aka low speed rolling in the neighborhood) The real culprit is at the mechanical design of this thing.

Most people complain about slow speed driving in the 30-45mph range.

This might be placebo or I’m just crazy. During your 500mile learning period drive the van with Econ off and drive it how you expect to accelerate and such. After that learning takes place and complete go back to driving gentle and with Econ. Feel like this made a difference in my van. 🤷‍♂️ Goal is longevity. As long as it doesn’t completely poop out I am ok with it. I’ve done 2 cross country trips and had no issues got great mpg at 29.3.
All best. And keep us posted.
 

· Registered
2019 EX-L
Joined
·
306 Posts
Discussion Starter · #26 ·
The van drives so much better after the TSB... it doesn’t slam into gear around 24-27 mph like it used to and I drove it how I knew I could duplicate the issue and had no problems. I’ll post updates after 500-1k miles. Time will tell.
That's great to hear!
 
  • Like
Reactions: Aclement1618

· Registered
2019 EX-L
Joined
·
306 Posts
Discussion Starter · #30 · (Edited)
Transmission failed on 3/14 while we a were on a spring break road trip. It's 3/23 and it still hasn't been fixed, and we have been stranded for days out of town waiting for it to be completed.
This is my worst fear. So sorry to hear this. Hope you dont have to wait too much longer. Honda needs to understand there is a pandemic out there and take some responsibility.
Thank you for posting and taking the survey. This is why we have this here.

All the best and keep us updated on what Honda does. If the new transmission is any better.

Also did you get fluid change by any chance? Did the transmission act funny before all this?
 

· Registered
2019 EX-L
Joined
·
306 Posts
Discussion Starter · #34 ·
Honda has replaced the transmission with another 9 speed transmission, and we are finally on our drive home. I would say that the transmission would lag at times when I accelerated in the past, but nothing that had bothered me enough to get it looked at.
Glad you all are on your way home. Keep us posted on how this "new" transmission behaves. If it's the exact same or improved compared to the one that failed. Drive safe!
 

· Registered
2019 EX-L
Joined
·
306 Posts
Discussion Starter · #41 ·
2021 Toyota Sienna.
Very nice. Best of luck!
My goal is to keep mine as long as possible. Bought new all paid for. It’s a big loss if I sell/trade now. So far no issues and hoping it will stay that way.
 
  • Like
Reactions: Aclement1618

· Registered
2019 EX-L
Joined
·
306 Posts
Discussion Starter · #47 ·
Short answer no.
Yup. This. This is what the complaints are all about. Unfortunately this is how this AT behaves... by design... not the answer you want. It’s not the greatest AT. Part of me is like this is just a minivan of all things. Considering $36k hard earned $ this is not acceptable. This gets worse bc you think about it and dwell on on it. This is why I will be buying last year of a particular gen of any make/model. We are beta testers otherwise. No complaints from my van but I do get the dog clutch clicks. I worry as I see more complaints here. Longevity is what I seek over shift quality.
 
  • Like
Reactions: Aclement1618

· Registered
2019 EX-L
Joined
·
306 Posts
Discussion Starter · #50 ·
Bump

We need to report here instead of starting another transmission failure thread. Wish we could get it pinned. I’ve manually added in the number of failures on the 1st post for those the didn’t place their vote in the survey

survey input + reports on other threads we have these numbers below. Happy to report not all 5th gen odyssey’s out there are blowing up folks.

[9 speed failures: 4]
[10 Speed failures: 8]
 

· Registered
2019 EX-L
Joined
·
306 Posts
Discussion Starter · #55 ·
Brand new 2022 Odyssey EX-L with 100 miles on the odometer and the transmission is toast.
Sorry to hear this. Thanks for reporting. Glad it is covered by warranty. Hate to wrench on a new vehicle 😕

Is your other forum name AmericanOperator? Checking for a friend. ;)
LOL
 
1 - 20 of 38 Posts
Top